[Sidenote: Eyelets]

Eyelet holes are made with a stiletto which forces the threads aside, but does not cut them. The edge is finished with over and over stitches placed closely together, or with a buttonhole stitch making the purl on the outer edge of the stitches. Loops are made by buttonholing very closely over several foundation threads, making the purl on the outside edge. The needle may be run under the loop eye first if preferred.

PATCHING

[Sidenote: Underset Patch]

With the underset patch have the part to be patched pressed smooth, baste the patch on the wrong side of the garment before cutting out the worn place. (If the garment or article to be mended is worn or faded and shrunken by laundering, boil the piece in soap, soda and water to fade the patch, if of cotton or linen.) After basting, cut away all the worn cloth, making a square or oblong hole. Cut to a thread. Cut each corner, diagonally, one-eighth or one-quarter of an inch, turn all four edges of the garment towards the wrong side. Begin at the center of one side and hem all around the square, taking slanting even stitches, not too close together. Remove the basting, trim the edges of the patch, press the patch on the wrong side and catch stitch to the garment. This shows less on the right side and does not make a hard line as if the patch were turned back on the edge. If the cloth has a pattern or stripe, match it perfectly, having the warp threads of both running the same way. Cut both hole and patch square. An oval or round patch is unworkmanlike and does not wear well. Keep the corners square and hem down well. The object of pressing is to keep both garment and patch flat and even. Flannel patches should be cat-stitched on the right side. No flannel edges should ever be inturned.

[Sidenote: Onset Patch]

The onset patch is used on lined garments and linings. The patch should be rectangular and larger than the worn place. Fold the four edges on the wrong side of the patch, place the patch with its wrong side on the right side of the garment directly over the center of the hole. This will bring the folded edges of the patch between the two pieces of cloth and both right sides towards the worker. Do not baste, but pin carefully. After the garment has been folded back until there are two folded edges side by side, overhand the seam with even slanting stitches. See that the corners are well sewed, that warp and woof threads run in the same direction, that pattern and stripes match.

The worn part of the garment under the patch is cut away, leaving one-fourth of an inch on the three sides. Cut the corners diagonally and turn back the edge quarter of an inch, overcast and press. If this patch is sewed on a lining, the worn part is not cut away. If this patch is used to repair skirts near the band, only three sides are oversewed, the upper edge should be gathered into the band. A large patch is less conspicuous than a small one.

[Sidenote: Patch for Trowsers]

An onset patch may be used for the seats of trousers by shaping the patch like the pieces on the seats of bicycle trousers and stitching on the machine. Heavy cloth will need no inturned edges. The same precautions are necessary regarding warp and woof, pattern, etc.

DARNING

[Sidenote: Thread for Darning]

Darning is usually done with a running stitch, with or without a piece of net or cloth underset. Thread for darning should be as near as possible the size of the threads in the garment. Whenever it can be done, a warp thread of the garment should be used. No sewing silk is fine enough to use without separating the thread and using one of the strands. Never use the thread as it is, as it is too hard twisted. Cotton and linen thread of the finest quality, untwisted, should be used for darning stockings and underwear. Linen may be darned with linen or mercerized cotton. Cotton is preferable.

A long slender needle with a large eye should be used. Darning should never be commenced with a knot, nor finished with a back stitch.

[Sidenote: Bias Darn]

A bias or diagonal cut and a three-cornered tear are the most difficult to repair. If the place is badly pulled and frayed, a piece of the same material should be basted on the wrong side of the material and darned in even stitches. Always darning parallel with the warp threads and the woof threads. In the diagonal tear, as the threads are cut diagonally, to prevent drawing apart, the darning threads must cross each other.

The stitches around any darn should not end in a stiff even line; this makes a hard edge which does not wear and is unsightly, and uncomfortable if on underwear.

[Sidenote: Darning a Three Cornered Tear]

The three-cornered tear may be darned in two ways. Begin by darning diagonally through the center, darning back and forth towards the end of the tear until one-half has been finished; then begin at the center and work in the opposite direction. At the corner, the stitches should form the shape of a fan. The other method, which is the stronger, is done by darning a square in the angle, first with the warp threads, then with the woof threads and finishing each end across the tear.

Stocking darning may be done on the right side. Begin by picking up the stitches and drawing the edges together. This should always be done in any kind of stocking darning, but not so close as to make a wrinkle.

In knees and heels of stockings, or knitted underwear, a piece of net large enough to extend beyond the thin part should be basted carefully; then darn down the outer edges of the net and finally the hole or thin place. This makes a strong, neat piece of mending. If the hole is large, the net may be covered with the chain stitch, thus imitating the knitting stitch. This should be done on the right side of the garment.

If the hole is to be filled in with the interlaced stitches, draw the edges together, darn beyond the thin places lengthwise of the knitted garment, making each line of stitches longer until the center of the hole is reached, then decrease in the same manner, making a diamond in shape. Darn across the hole in the same way, taking up every alternate stitch as in weaving. Leave a tiny loop at the end of each row of darning, so that the threads will not draw.

[Sidenote: Machine Darning]

Darning, satisfactory for some purposes, may be done quickly on a double thread sewing machine. It is best done in an embroidery ring, first drawing the edges together. Loosen the tension on the presser foot, use fine thread with light tension. Sew back and forth, first along the warp threads and then at right angles along the woof threads. The machine will be sewing backwards part of the time, but if the pressure is light, there will be no difficulty. For large holes, paper may be placed underneath.

MITERING EMBROIDERY OR LACE

The mitering of lace or embroidery is often necessary in making collars and in finishing corners. Before applying, plan carefully and select a scallop or portion of the embroidery which will produce the best effects when finished. This can be accomplished by folding the embroidery over at various portions of the pattern until a suitable point is found. Fold over at right angles and mark along the line to be mitered. The triangle may now be cut, but an extra width must always be allowed for the seam, as there is frequently a slight unevenness and one side may have to be held a little full or stretched to make a perfect match. The mitered seam is over-sewed.

After the corner is properly made, cut away the cloth of the embroidery, allowing only enough for an inturned seam on the edge. This seam may be stitched on the machine on both edges, or oversewed to the goods, or the embroidery may be securely sewed on the plain part, after which the underlying cloth may be cut away. This will make an almost perfect corner.

Lace may be matched and mitered in a similar way.

MATCHING AND JOINING LACE

In joining lace, avoid a seam if possible. Select portions of the design that will match, placing one pattern of the same design over the other. Cut away a portion of the thick part of the pattern underneath and hem the edges and inner part of the design down with fine thread.

Smyrna or Torchon lace is more difficult to hem or join when very open or very fine. A small, felled seam is better than lapping and trying to match the pattern.

Embroidery can be matched in the same way. Never let two heavy designs lap over each other. The one on the wrong side should be cut out and the edge sewed securely to the upper part of the design.

The plain material above the embroidery can be joined by a lapped seam, turning first the right side and then the wrong side and hemming on both sides of the seam.

MACHINE SEWING

The sewing machine has taken away much of the drudgery of home sewing, but its use does not lessen the need of skill in hand work. No machine can finish ends of belts, collars, sew on trimmings, fastenings, and like work and the finish has much to do with the general appearance of a garment.

[Sidenote: Types of Machines]